Marvell 8686 sdio in ARM11 linux2.6.24.2

[Dan Williams]

On Mon, 2009-08-03 at 11:29 +0800, tommy wrote:
> hi,all!My ARM11 met a marvell8686 problem!It is similiar with
> http://lists.infradead.org/pipermail/libertas-dev/2008-June/001721.html!
> 
> following is my debug!

Any chance you could turn on MMC/SDIO stack debugging?  Need to see what
the stack thinks is happening.  Also, you might try backporting later
versions of the libertas driver (2.6.29 or so) since quite a few fixes
have happened since the libertas-sdio bits first landed in 2.6.24.

Dan

> 1:
> root at localhost:/root# 
> 
> ** (nm-applet:828): WARNING **: <WARN>  nm_gconf_get_keyring_items():
> key: /system/networking/private-data/k
> 
> 
> Trying to associate with 00:1c:b0:91:6e:8c (SSID='midfun' freq=2437 MHz)
> ioctl[SIOCSIWAUTH]: Operation not supported
> WEXT auth param 10 value 0x1 - ioctl[SIOCSIWAUTH]: Operation not
> supported
> WEXT auth param 8 value 0x0 - Association request to the driver failed
> Associated with 00:1c:b0:91:6e:8c
> WPA: Key negotiation completed with 00:1c:b0:91:6e:8c [PTK=CCMP
> GTK=TKIP]
> CTRL-EVENT-CONNECTED - Connection to 00:1c:b0:91:6e:8c completed (auth)
> [id=0 id_str=]
> mmc1: Got command interrupt 0x00008000 even though no command operation
> was in progress.
> mmc1: Got command interrupt 0x00008000 even though no command operation
> was in progress.
> 
> 2:root at localhost:/root# ping -s 5000 210.28.95.230
> PING 210.28.95.230 (210.28.95.230): 5000 data bytes
> mmc1: Got command interrupt 0x00008000 even though no command operation
> was in progress.
> mmc1: Got command interrupt 0x00008000 even though no command operation
> was in progress.
> mmc1: Got command interrupt 0x00008000 even though no command operation
> was in progress.
> 5008 bytes from 210.28.95.230: seq=0 ttl=48 time=86.571 ms
> mmc1: Got command interrupt 0x00008000 even though no command operation
> was in progress.
> mmc1: Got command interrupt 0x00008000 even though no command operation
> was in progress.
> mmc1: Got command interrupt 0x00008000 even though no command operation
> was in progress.
> mmc1: Got command interrupt 0x00008000 even though no command operation
> was in progress.
> 5008 bytes from 210.28.95.230: seq=1 ttl=48 time=89.089 ms
> mmc1: Got command interrupt 0x00008000 even though no command operation
> was in progress.
> mmc1: Got command interrupt 0x00008000 even though no command operation
> was in progress.
> mmc1: Got command interrupt 0x00008000 even though no command operation
> was in progress.
> 5008 bytes from 210.28.95.230: seq=2 ttl=48 time=85.210 ms
> mmc1: Got command interrupt 0x00008000 even though no command operation
> was in progress.
> NETDEV WATCHDOG: eth3: transmit timed out
> 
> 
> Someone can posted some patch for that?My bsp is 2.6.24 libertas driver
> for marvell8686!
> 
> Thanks !
> 
> 
> _______________________________________________
> libertas-dev mailing list
> libertas-dev at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/libertas-dev