[ 0.000000] Linux version 2.6.26-rc6-epm-14-git-debug-patch (root@debian-workstation) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 PREEMPT Thu Jun 12 17:38:06 PDT 2008 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009e400 (usable) [ 0.000000] BIOS-e820: 000000000009e400 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000000dbe9000 (usable) [ 0.000000] BIOS-e820: 000000000dbe9000 - 0000000010000000 (reserved) [ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) [ 0.000000] 0MB HIGHMEM available. [ 0.000000] 219MB LOWMEM available. [ 0.000000] Entering add_active_range(0, 0, 56297) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 56297 [ 0.000000] HighMem 56297 -> 56297 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 56297 [ 0.000000] On node 0 totalpages: 56297 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 408 pages used for memmap [ 0.000000] Normal zone: 51793 pages, LIFO batch:15 [ 0.000000] HighMem zone: 0 pages used for memmap [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] DMI 2.1 present. [ 0.000000] ACPI Error (tbxfroot-0218): A valid RSDP was not found [20080321] [ 0.000000] Allocating PCI resources starting at 20000000 (gap: 10000000:eff00000) [ 0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000 [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000dc000 [ 0.000000] PM: Registered nosave memory: 00000000000dc000 - 0000000000100000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 55857 [ 0.000000] Kernel command line: root=/dev/hda1 ro video=lxfb:1024x768@60 [ 0.000000] No local APIC present or hardware disabled [ 0.000000] mapped APIC to ffffb000 (011bb000) [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes) [ 0.000000] Detected 498.066 MHz processor. [ 0.004000] Console: colour VGA+ 80x25 [ 0.004000] console [tty0] enabled [ 0.004000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.004000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.004000] Memory: 219132k/225188k available (2069k kernel code, 5556k reserved, 909k data, 288k init, 0k highmem) [ 0.004000] virtual kernel memory layout: [ 0.004000] fixmap : 0xfffa8000 - 0xfffff000 ( 348 kB) [ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 0.004000] vmalloc : 0xce800000 - 0xff7fe000 ( 783 MB) [ 0.004000] lowmem : 0xc0000000 - 0xcdbe9000 ( 219 MB) [ 0.004000] .init : 0xc03ec000 - 0xc0434000 ( 288 kB) [ 0.004000] .data : 0xc0305799 - 0xc03e8ca0 ( 909 kB) [ 0.004000] .text : 0xc0100000 - 0xc0305799 (2069 kB) [ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated [ 0.084451] Calibrating delay using timer specific routine.. 997.77 BogoMIPS (lpj=1995541) [ 0.084787] Mount-cache hash table entries: 512 [ 0.085282] CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line) [ 0.085370] CPU: L2 Cache: 128K (32 bytes/line) [ 0.085462] CPU: AMD Geode(TM) Integrated Processor by AMD PCS stepping 02 [ 0.085686] Checking 'hlt' instruction... OK. [ 0.100552] Freeing SMP alternatives: 0k freed [ 0.100628] ACPI: Core revision 20080321 [ 0.100819] ACPI Exception (tbxface-0629): AE_NO_ACPI_TABLES, While loading namespace from ACPI tables [20080321] [ 0.101016] ACPI: Unable to load the System Description Tables [ 0.101769] net_namespace: 196 bytes [ 0.102632] NET: Registered protocol family 16 [ 0.103510] EISA bus registered [ 0.105662] PCI: PCI BIOS revision 2.10 entry at 0xff699, last bus=0 [ 0.105747] PCI: Using configuration type 1 for base access [ 0.105855] Setting up standard PCI resources [ 0.113832] ACPI: Interpreter disabled. [ 0.113913] Linux Plug and Play Support v0.97 (c) Adam Belay [ 0.114096] pnp: PnP ACPI: disabled [ 0.114172] PnPBIOS: Scanning system for PnP BIOS support... [ 0.114620] PnPBIOS: PnP BIOS support was not detected. [ 0.115467] SCSI subsystem initialized [ 0.116111] PCI: Probing PCI hardware [ 0.116187] PCI: Probing PCI hardware (bus 00) [ 0.147477] NET: Registered protocol family 2 [ 0.147927] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.148059] Switched to high resolution mode on CPU 0 [ 0.149177] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.149450] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [ 0.149667] TCP: Hash tables configured (established 8192 bind 8192) [ 0.149749] TCP reno registered [ 0.150095] NET: Registered protocol family 1 [ 0.152474] audit: initializing netlink socket (disabled) [ 0.152583] type=2000 audit(1212710680.152:1): initialized [ 0.153789] msgmni has been set to 428 [ 0.154093] io scheduler noop registered [ 0.154166] io scheduler anticipatory registered [ 0.154242] io scheduler deadline registered [ 0.154357] io scheduler cfq registered (default) [ 0.154622] pci 0000:00:01.1: Boot video device [ 0.154656] pci 0000:00:0d.0: Firmware left e100 interrupts enabled; disabling [ 0.154767] pci 0000:00:0e.0: Firmware left e100 interrupts enabled; disabling [ 0.169388] GEODE: VSA SIG = 534d [ 0.169461] GEODE: read from descriptor [ 0.169531] GEODE: Return 4000<6>lxfb 0000:00:01.1: 16 KB of video memory at 0xe0000000 [ 0.169743] lxfb 0000:00:01.1: could not find valid video mode [ 0.169844] lxfb: probe of 0000:00:01.1 failed with error -22 [ 0.170390] isapnp: Scanning for PnP cards... [ 0.528951] isapnp: No Plug & Play device found [ 0.538305] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 0.538679] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.539032] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 0.545348] brd: module loaded [ 0.545425] HP CISS Driver (v 3.6.14) [ 0.545653] Uniform Multi-Platform E-IDE driver [ 0.545741] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 0.546127] AMD5536: 0000:00:0f.2 (rev 01) UDMA100 controller [ 0.546213] AMD5536: IDE controller (0x1022:0x209a rev 0x01) at PCI slot 0000:00:0f.2 [ 0.546827] AMD5536: not 100% native mode: will probe irqs later [ 0.547524] AMD5536: IDE port disabled [ 0.547729] ide0: BM-DMA at 0xd800-0xd807 [ 0.547811] Probing IDE interface ide0... [ 0.836192] hda: WDC WD800BB-00JHC0, ATA DISK drive [ 1.508448] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4 [ 1.509175] hda: host side 80-wire cable detection failed, limiting max speed to UDMA33 [ 1.509279] hda: UDMA/33 mode selected [ 1.509964] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 1.510631] ide_generic: I/O resource 0x1F0-0x1F7 not free. [ 1.510716] ide_generic: I/O resource 0x170-0x177 not free. [ 1.511069] hda: max request size: 128KiB [ 1.517996] hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63 [ 1.517996] hda: cache flushes supported [ 1.517996] hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 > [ 1.581079] ide-floppy driver 1.00 [ 1.581387] Driver 'sd' needs updating - please use bus_type methods [ 1.581590] Driver 'sr' needs updating - please use bus_type methods [ 1.582421] PNP: No PS/2 controller found. Probing ports directly. [ 1.589844] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.589935] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 1.590552] mice: PS/2 mouse device common for all mice [ 1.590868] WDT driver for Acquire single board computer initialising. [ 1.594020] acquirewdt: I/O address 0x0043 already in use [ 1.594112] acquirewdt: probe of acquirewdt failed with error -5 [ 1.594468] EISA: Probing bus 0 at eisa.0 [ 1.594741] EISA: Mainboard @@@0000 detected. [ 1.595048] EISA: Detected 0 cards. [ 1.595122] cpuidle: using governor ladder [ 1.595203] cpuidle: using governor menu [ 1.598157] TCP cubic registered [ 1.598235] NET: Registered protocol family 17 [ 1.598328] Using IPI Shortcut mode [ 1.792236] atkbd.c: Failed to enable keyboard on isa0060/serio0 [ 1.792787] input: AT Translated Set 2 keyboard as /class/input/input0 [ 1.836018] kjournald starting. Commit interval 5 seconds [ 1.836018] EXT3-fs: mounted filesystem with ordered data mode. [ 1.836018] VFS: Mounted root (ext3 filesystem) readonly. [ 1.836018] Freeing unused kernel memory: 288k freed [ 4.987776] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI [ 4.987882] e100: Copyright(c) 1999-2006 Intel Corporation [ 5.051822] cs5535_gpio: base=0xec00 mask=0xb003c66 major=254 [ 5.229389] e100: eth0: e100_probe: addr 0xe2010000, irq 11, MAC addr 00:04:bf:00:00:01 [ 5.349045] input: PC Speaker as /class/input/input1 [ 5.358102] e100: eth1: e100_probe: addr 0xe2040000, irq 11, MAC addr 00:04:bf:00:00:02 [ 5.365772] usbcore: registered new interface driver usbfs [ 5.365959] usbcore: registered new interface driver hub [ 5.373947] usbcore: registered new device driver usb [ 5.390221] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 5.390967] PCI: Setting latency timer of device 0000:00:0f.4 to 64 [ 5.391082] ohci_hcd 0000:00:0f.4: OHCI Host Controller [ 5.391454] ohci_hcd 0000:00:0f.4: new USB bus registered, assigned bus number 1 [ 5.391583] ohci_hcd 0000:00:0f.4: irq 9, io mem 0xe2080000 [ 5.575443] usb usb1: configuration #1 chosen from 1 choice [ 5.575682] hub 1-0:1.0: USB hub found [ 5.575778] hub 1-0:1.0: 4 ports detected [ 5.677288] PCI: Setting latency timer of device 0000:00:0f.5 to 64 [ 5.677405] ehci_hcd 0000:00:0f.5: EHCI Host Controller [ 5.677589] ehci_hcd 0000:00:0f.5: new USB bus registered, assigned bus number 2 [ 5.700544] ehci_hcd 0000:00:0f.5: irq 9, io mem 0xe2081000 [ 5.712060] ehci_hcd 0000:00:0f.5: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 [ 5.712481] usb usb2: configuration #1 chosen from 1 choice [ 5.712698] hub 2-0:1.0: USB hub found [ 5.712792] hub 2-0:1.0: 4 ports detected [ 5.948372] input: PS/2 Generic Mouse as /class/input/input2 [ 6.636063] usb 1-3: new low speed USB device using ohci_hcd and address 2 [ 6.855361] usb 1-3: configuration #1 chosen from 1 choice [ 7.158010] Adding 995988k swap on /dev/hda7. Priority:-1 extents:1 across:995988k [ 7.160083] usb 1-4: new low speed USB device using ohci_hcd and address 3 [ 7.368346] usb 1-4: configuration #1 chosen from 1 choice [ 7.372812] usbcore: registered new interface driver hiddev [ 7.378910] input: Logitech Optical USB Mouse as /class/input/input3 [ 7.404762] input,hidraw0: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:0f.4-3 [ 7.408976] EXT3 FS on hda1, internal journal [ 7.411542] input: HID 0566:3002 as /class/input/input4 [ 7.436267] input,hidraw1: USB HID v1.10 Keyboard [HID 0566:3002] on usb-0000:00:0f.4-4 [ 7.449771] input: HID 0566:3002 as /class/input/input5 [ 7.476389] input,hiddev96,hidraw2: USB HID v1.10 Device [HID 0566:3002] on usb-0000:00:0f.4-4 [ 7.476832] usbcore: registered new interface driver usbhid [ 7.476916] usbhid: v2.6:USB HID core driver [ 10.186876] loop: module loaded [ 13.228104] floppy0: no floppy controllers found [ 15.252273] e100: eth0: e100_watchdog: link up, 100Mbps, half-duplex