libertas: command 1f timed out error

Sat Sep 27 01:43:03 EDT 2008

hi

> Argh, I forgot to tell you to build the module with
> CONFIG_LIBERTAS_DEBUG (or LIBERTAS_DEBUG=y) selected.  Or just #define
> that at the top of defs.h if you don't want to do a full kernel compile.
>
> Also, what SDIO controller are you using?

I am using AT91SAM9260 microcontroller with arm926ej-s
processor.I am using arm-linux OS in my target eval board for
at91sam9260.

http://www.atmel.com/dyn/resources/prod_documents/doc6221.pdf

Thanks for pointing me to enable the libertas_debug.

Here is the kernel log messages from /var/log/messages

Since the log messages is very long...i am posting the messages from
the moment i issue

Please guide me whether it is a host controller error or the marvell
firmware error or the libertas driver error ????

#dhclient eth1 command....

Dec 31 17:03:26 ekadesigns daemon.info dhclient: Internet Systems
Consortium DHCP Client V3.0.5
Dec 31 17:03:26 ekadesigns user.debug kernel: mmc0: req done (CMD52):
0: 00001000 006e0000 0063006f 006c0061
Dec 31 17:03:26 ekadesigns daemon.info dhclient: Copyright 2004-2006
Internet Systems Consortium.
Dec 31 17:03:26 ekadesigns user.debug kernel: mmc0: starting CMD52 arg
00000a00 flags 00000195
Dec 31 17:03:26 ekadesigns daemon.info dhclient: All rights reserved.
Dec 31 17:03:26 ekadesigns user.debug kernel: Sending command 52 as
00001074, arg = 00000A00, blocks = 0, length = 0 (MR = 007C9B01)
Dec 31 17:03:26 ekadesigns daemon.info dhclient: For info, please
visit http://www.isc.org/sw/dhcp/
Dec 31 17:03:26 ekadesigns user.debug kernel: MCI irq: status =
0000C0E5, C07F0001, 00000001
Dec 31 17:03:26 ekadesigns daemon.info dhclient:
Dec 31 17:03:26 ekadesigns user.debug kernel: Command ready
Dec 31 17:03:26 ekadesigns user.debug kernel: Completed command
Dec 31 17:03:26 ekadesigns user.debug kernel: Status = 0000C0E5
[00001000 006E0000 0063006F 006C0061]
Dec 31 17:03:26 ekadesigns user.debug kernel: mmc0: req done (CMD52):
0: 00001000 006e0000 0063006f 006c0061
Dec 31 17:03:26 ekadesigns user.debug kernel: mmc0: starting CMD52 arg
00000a00 flags 00000195
Dec 31 17:03:26 ekadesigns user.debug kernel: Sending command 52 as
00001074, arg = 00000A00, blocks = 0, length = 0 (MR = 007C9B01)
Dec 31 17:03:26 ekadesigns user.debug kernel: MCI irq: status =
0000C0E5, C07F0001, 00000001
Dec 31 17:03:26 ekadesigns user.debug kernel: Command ready
Dec 31 17:03:26 ekadesigns daemon.info dhclient: Listening on
LPF/eth1/00:19:88:05:10:17
Dec 31 17:03:26 ekadesigns user.debug kernel: Completed command
Dec 31 17:03:26 ekadesigns daemon.info dhclient: Sending on
LPF/eth1/00:19:88:05:10:17
Dec 31 17:03:26 ekadesigns user.debug kernel: Status = 0000C0E5
[00001000 006E0000 0063006F 006C0061]
Dec 31 17:03:26 ekadesigns daemon.info dhclient: Sending on   Socket/fallback
Dec 31 17:03:26 ekadesigns user.debug kernel: mmc0: req done (CMD52):
0: 00001000 006e0000 0063006f 006c0061
Dec 31 17:03:26 ekadesigns user.debug kernel: mmc0: starting CMD52 arg
00000a00 flags 00000195
Dec 31 17:03:43 ekadesigns user.debug kernel: Sending command 52 as
00001074, arg = 10004000, blocks = 0, length = 0 (MR = 01009B01)
Dec 31 17:03:43 ekadesigns user.debug kernel: MCI irq: status =
0000C0C5, C07F0001, 00000001
Dec 31 17:03:43 ekadesigns user.debug kernel: Command ready
Dec 31 17:03:43 ekadesigns user.debug kernel: Completed command
Dec 31 17:03:43 ekadesigns user.debug kernel: Status = 0000C0C5
[0000100A 00000000 00000000 00000000]
Dec 31 17:03:43 ekadesigns user.debug kernel: mmc0: req done (CMD52):
0: 0000100a 00000000 00000000 00000000
Dec 31 17:03:43 ekadesigns user.debug kernel: mmc0: starting CMD53 arg
1200005c flags 000001b5
Dec 31 17:03:43 ekadesigns user.debug kernel: mmc0:     blksz 92
blocks 1 flags 00000200 tsac 1000 ms nsac 0
Dec 31 17:03:43 ekadesigns user.debug kernel: Sending command 53 as
00051075, arg = 1200005C, blocks = 1, length = 92 (MR = 01009B01)
Dec 31 17:03:44 ekadesigns user.debug kernel: pre dma read
Dec 31 17:03:44 ekadesigns user.debug kernel: Using transfer index 0
Dec 31 17:03:44 ekadesigns user.debug kernel: sg = c30ddec8
Dec 31 17:03:44 ekadesigns user.debug kernel: dma address = 23120018,
length = 92
Dec 31 17:03:44 ekadesigns user.debug kernel: Nothing left to transfer
(index = 1)
Dec 31 17:03:44 ekadesigns user.debug kernel: pre dma read done
Dec 31 17:03:44 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:03:44 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:03:44 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:03:44 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:03:44 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:03:44 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 0, bytes 366):702
Dec 31 17:03:44 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:03:44 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=1
Dec 31 17:03:44 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:03:44 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card_worker():354
Dec 31 17:03:44 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=1
Dec 31 17:03:44 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=1
Dec 31 17:03:44 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=1
Dec 31 17:03:44 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=1
Dec 31 17:03:44 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:03:49 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:03:49 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas enter (INT):
lbs_set_cmd_ctrl_node():1718
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas leave (INT):
lbs_set_cmd_ctrl_node():1726
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: command 0x001f
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas enter (INT):
lbs_cmd_802_11_rssi():828
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas leave (INT):
lbs_cmd_802_11_rssi():841
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas enter (INT):
lbs_queue_cmd():1091
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas host (INT):
QUEUE_CMD: inserted command 0x001f into cmdpendingq
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas leave (INT):
lbs_queue_cmd():1126
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret 0
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 39, size 16, jiffies 4294960200
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 4294960200
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:03:49 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:03:50 ekadesigns daemon.info dhclient: DHCPDISCOVER on eth1
to 255.255.255.255 port 67 interval 19
Dec 31 17:03:54 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:03:54 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:03:54 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:03:54 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:03:54 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:03:54 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:03:54 ekadesigns user.info kernel: libertas: requeueing
command 1f due to timeout (#1)
Dec 31 17:03:54 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:03:54 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:03:59 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:03:59 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas enter (INT):
lbs_set_cmd_ctrl_node():1718
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas leave (INT):
lbs_set_cmd_ctrl_node():1726
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: command 0x001f
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas enter (INT):
lbs_cmd_802_11_rssi():828
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas leave (INT):
lbs_cmd_802_11_rssi():841
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas enter (INT):
lbs_queue_cmd():1091
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas host (INT):
QUEUE_CMD: inserted command 0x001f into cmdpendingq
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas leave (INT):
lbs_queue_cmd():1126
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret 0
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 39, size 16, jiffies 4294961200
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 4294961200
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:03:59 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:04:04 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:04:04 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:04:04 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:04:04 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:04:04 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:04 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:04 ekadesigns user.info kernel: libertas: requeueing
command 1f due to timeout (#2)
Dec 31 17:04:04 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:04 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:04:09 ekadesigns daemon.info dhclient: DHCPDISCOVER on eth1
to 255.255.255.255 port 67 interval 18
Dec 31 17:04:09 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:04:09 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas enter (INT):
lbs_set_cmd_ctrl_node():1718
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas leave (INT):
lbs_set_cmd_ctrl_node():1726
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: command 0x001f
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas enter (INT):
lbs_cmd_802_11_rssi():828
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas leave (INT):
lbs_cmd_802_11_rssi():841
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas enter (INT):
lbs_queue_cmd():1091
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas host (INT):
QUEUE_CMD: inserted command 0x001f into cmdpendingq
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas leave (INT):
lbs_queue_cmd():1126
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret 0
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 39, size 16, jiffies 4294962200
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 4294962200
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:09 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:04:14 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:04:14 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:04:14 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:04:14 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:04:14 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:14 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:14 ekadesigns user.info kernel: libertas: requeueing
command 1f due to timeout (#3)
Dec 31 17:04:14 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:14 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:04:19 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:04:19 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas enter (INT):
lbs_set_cmd_ctrl_node():1718
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas leave (INT):
lbs_set_cmd_ctrl_node():1726
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: command 0x001f
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas enter (INT):
lbs_cmd_802_11_rssi():828
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas leave (INT):
lbs_cmd_802_11_rssi():841
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas enter (INT):
lbs_queue_cmd():1091
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas host (INT):
QUEUE_CMD: inserted command 0x001f into cmdpendingq
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas leave (INT):
lbs_queue_cmd():1126
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret 0
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 39, size 16, jiffies 4294963200
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 4294963200
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:19 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:04:24 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:04:24 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:04:24 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:04:24 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:04:24 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:24 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:24 ekadesigns user.info kernel: libertas: requeueing
command 1f due to timeout (#4)
Dec 31 17:04:24 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:24 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:04:27 ekadesigns daemon.info dhclient: DHCPDISCOVER on eth1
to 255.255.255.255 port 67 interval 4
Dec 31 17:04:29 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:04:29 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas enter (INT):
lbs_set_cmd_ctrl_node():1718
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas leave (INT):
lbs_set_cmd_ctrl_node():1726
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: command 0x001f
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas enter (INT):
lbs_cmd_802_11_rssi():828
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas leave (INT):
lbs_cmd_802_11_rssi():841
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas enter (INT):
lbs_queue_cmd():1091
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas host (INT):
QUEUE_CMD: inserted command 0x001f into cmdpendingq
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas leave (INT):
lbs_queue_cmd():1126
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret 0
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 39, size 16, jiffies 4294964200
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 4294964200
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:29 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:04:31 ekadesigns daemon.info dhclient: No DHCPOFFERS received.
Dec 31 17:04:31 ekadesigns daemon.info dhclient: No working leases in
persistent database - sleeping.
Dec 31 17:04:34 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:04:34 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:04:34 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:04:34 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:04:34 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:34 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:34 ekadesigns user.info kernel: libertas: requeueing
command 1f due to timeout (#5)
Dec 31 17:04:34 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:34 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:04:39 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:04:39 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas enter (INT):
lbs_set_cmd_ctrl_node():1718
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas leave (INT):
lbs_set_cmd_ctrl_node():1726
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: command 0x001f
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas enter (INT):
lbs_cmd_802_11_rssi():828
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas leave (INT):
lbs_cmd_802_11_rssi():841
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas enter (INT):
lbs_queue_cmd():1091
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas host (INT):
QUEUE_CMD: inserted command 0x001f into cmdpendingq
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas leave (INT):
lbs_queue_cmd():1126
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret 0
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 39, size 16, jiffies 4294965200
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 4294965200
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:39 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:04:44 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:04:44 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:04:44 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:04:44 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:04:44 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:44 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:44 ekadesigns user.info kernel: libertas: requeueing
command 1f due to timeout (#6)
Dec 31 17:04:44 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:44 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:04:49 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:04:49 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas enter (INT):
lbs_set_cmd_ctrl_node():1718
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas leave (INT):
lbs_set_cmd_ctrl_node():1726
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: command 0x001f
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas enter (INT):
lbs_cmd_802_11_rssi():828
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas leave (INT):
lbs_cmd_802_11_rssi():841
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas enter (INT):
lbs_queue_cmd():1091
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas host (INT):
QUEUE_CMD: inserted command 0x001f into cmdpendingq
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas leave (INT):
lbs_queue_cmd():1126
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret 0
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 39, size 16, jiffies 4294966200
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 4294966200
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:49 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:04:54 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:04:54 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:04:54 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:04:54 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:04:54 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:54 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:54 ekadesigns user.info kernel: libertas: requeueing
command 1f due to timeout (#7)
Dec 31 17:04:54 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:54 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:04:59 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out

Here is the complete list from /var/log/messages.0

Dec 31 17:04:59 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas enter (INT):
lbs_set_cmd_ctrl_node():1718
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas leave (INT):
lbs_set_cmd_ctrl_node():1726
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: command 0x001f
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas enter (INT):
lbs_cmd_802_11_rssi():828
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas leave (INT):
lbs_cmd_802_11_rssi():841
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas enter (INT):
lbs_queue_cmd():1091
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas host (INT):
QUEUE_CMD: inserted command 0x001f into cmdpendingq
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas leave (INT):
lbs_queue_cmd():1126
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret 0
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 39, size 16, jiffies 4294967200
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 4294967200
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:04:59 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:05:04 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:05:04 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:05:04 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:05:04 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:05:04 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:04 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:04 ekadesigns user.info kernel: libertas: requeueing
command 1f due to timeout (#8)
Dec 31 17:05:04 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:04 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:05:08 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:05:08 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas enter (INT):
lbs_set_cmd_ctrl_node():1718
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas leave (INT):
lbs_set_cmd_ctrl_node():1726
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: command 0x001f
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas enter (INT):
lbs_cmd_802_11_rssi():828
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas leave (INT):
lbs_cmd_802_11_rssi():841
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas enter (INT):
lbs_queue_cmd():1091
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas host (INT):
QUEUE_CMD: inserted command 0x001f into cmdpendingq
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas leave (INT):
lbs_queue_cmd():1126
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret 0
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 39, size 16, jiffies 900
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 900
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:09 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:05:13 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:05:13 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:05:14 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:05:14 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:05:14 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:14 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:14 ekadesigns user.info kernel: libertas: requeueing
command 1f due to timeout (#9)
Dec 31 17:05:14 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:14 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:05:18 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:05:18 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas enter (INT):
lbs_set_cmd_ctrl_node():1718
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas leave (INT):
lbs_set_cmd_ctrl_node():1726
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: command 0x001f
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas enter (INT):
lbs_cmd_802_11_rssi():828
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas leave (INT):
lbs_cmd_802_11_rssi():841
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas enter (INT):
lbs_queue_cmd():1091
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas host (INT):
QUEUE_CMD: inserted command 0x001f into cmdpendingq
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas leave (INT):
lbs_queue_cmd():1126
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret 0
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 39, size 16, jiffies 1900
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 1900
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:19 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:05:23 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:05:23 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:05:24 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:05:24 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:05:24 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:24 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:24 ekadesigns user.info kernel: libertas: requeueing
command 1f due to timeout (#10)
Dec 31 17:05:24 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:24 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:05:28 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:05:28 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas host (INT):
GET_CMD_NODE: cmd_ctrl_node is not available
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: cmdnode is NULL
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret -1
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 39, size 16, jiffies 2900
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 2900
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:29 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:05:33 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:05:33 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:05:34 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:05:34 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:05:34 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:34 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:34 ekadesigns user.info kernel: libertas: Excessive
timeouts submitting command 1f
Dec 31 17:05:34 ekadesigns user.debug kernel: libertas enter:
__lbs_cleanup_and_insert_cmd():1202
Dec 31 17:05:34 ekadesigns user.debug kernel: libertas leave:
__lbs_cleanup_and_insert_cmd():1214
Dec 31 17:05:34 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:34 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:05:38 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:05:38 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas enter (INT):
lbs_set_cmd_ctrl_node():1718
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas leave (INT):
lbs_set_cmd_ctrl_node():1726
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: command 0x001f
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas enter (INT):
lbs_cmd_802_11_rssi():828
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas leave (INT):
lbs_cmd_802_11_rssi():841
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas enter (INT):
lbs_queue_cmd():1091
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas host (INT):
QUEUE_CMD: inserted command 0x001f into cmdpendingq
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas leave (INT):
lbs_queue_cmd():1126
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: command failed with return code -110
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret -1
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 40, size 16, jiffies 3900
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 3900
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:39 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:05:40 ekadesigns user.err kernel: INFO: task ksdiorqd:840
blocked for more than 120 seconds.
Dec 31 17:05:40 ekadesigns user.err kernel: "echo 0 >
/proc/sys/kernel/hung_task_timeout_secs" disables this message.
Dec 31 17:05:40 ekadesigns user.info kernel: ksdiorqd      D c0252738
   0   840      2
Dec 31 17:05:40 ekadesigns user.warn kernel: [<c02524e4>]
(schedule+0x0/0x294) from [<c0252950>] (schedule_timeout+0x20/0xd0)
Dec 31 17:05:40 ekadesigns user.warn kernel: [<c0252930>]
(schedule_timeout+0x0/0xd0) from [<c02523b4>]
(wait_for_common+0xfc/0x198)
Dec 31 17:05:40 ekadesigns user.warn kernel:  r7:7fffffff r6:c30dde2c
r5:c30dc000 r4:c30ddde4
Dec 31 17:05:40 ekadesigns user.warn kernel: [<c02522b8>]
(wait_for_common+0x0/0x198) from [<c02524e0>]
(wait_for_completion+0x18/0x1c)
Dec 31 17:05:40 ekadesigns user.warn kernel:  r8:00000000 r7:c30a2800
r6:c30a2890 r5:c30ddeb4 r4:c30dde5c
Dec 31 17:05:40 ekadesigns user.warn kernel: [<c02524c8>]
(wait_for_completion+0x0/0x1c) from [<bf0009f8>]
(mmc_wait_for_req+0x1e0/0x200 [mmc_core])
Dec 31 17:05:40 ekadesigns user.warn kernel: [<bf000818>]
(mmc_wait_for_req+0x0/0x200 [mmc_core]) from [<bf00413c>]
(mmc_io_rw_extended+0x17c/0x1dc [mmc_core])
Dec 31 17:05:40 ekadesigns user.warn kernel:  r8:00010000 r7:c30a2c00
r6:00000001 r5:0000005c r4:c30dde5c
Dec 31 17:05:40 ekadesigns user.warn kernel: [<bf003fc0>]
(mmc_io_rw_extended+0x0/0x1dc [mmc_core]) from [<bf0051c0>]
(sdio_io_rw_ext_helper+0x104/0x13c [mmc_core])
Dec 31 17:05:40 ekadesigns user.warn kernel: [<bf0050bc>]
(sdio_io_rw_ext_helper+0x0/0x13c [mmc_core]) from [<bf005248>]
(sdio_readsb+0x24/0x2c [mmc_core])
Dec 31 17:05:40 ekadesigns user.warn kernel: [<bf005224>]
(sdio_readsb+0x0/0x2c [mmc_core]) from [<bf03e5f8>]
(if_sdio_interrupt+0x260/0x9dc [libertas_sdio])
Dec 31 17:05:40 ekadesigns user.warn kernel: [<bf03e398>]
(if_sdio_interrupt+0x0/0x9dc [libertas_sdio]) from [<bf0059e0>]
(sdio_irq_thread+0x110/0x228 [mmc_core])
Dec 31 17:05:40 ekadesigns user.warn kernel: [<bf0058d0>]
(sdio_irq_thread+0x0/0x228 [mmc_core]) from [<c0051bc0>]
(kthread+0x58/0x90)
Dec 31 17:05:40 ekadesigns user.warn kernel: [<c0051b68>]
(kthread+0x0/0x90) from [<c004166c>] (do_exit+0x0/0x610)
Dec 31 17:05:40 ekadesigns user.warn kernel:  r6:00000000 r5:00000000
r4:00000000
Dec 31 17:05:43 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:05:43 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:05:44 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:05:44 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:05:44 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:44 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:44 ekadesigns user.info kernel: libertas: requeueing
command 1f due to timeout (#1)
Dec 31 17:05:44 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:44 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:05:44 ekadesigns user.err kernel: INFO: task events/0:5
blocked for more than 120 seconds.
Dec 31 17:05:44 ekadesigns user.err kernel: "echo 0 >
/proc/sys/kernel/hung_task_timeout_secs" disables this message.
Dec 31 17:05:44 ekadesigns user.info kernel: events/0      D c0252738
   0     5      2
Dec 31 17:05:44 ekadesigns user.warn kernel: [<c02524e4>]
(schedule+0x0/0x294) from [<bf0006ac>] (__mmc_claim_host+0x98/0x104
[mmc_core])
Dec 31 17:05:44 ekadesigns user.warn kernel: [<bf000614>]
(__mmc_claim_host+0x0/0x104 [mmc_core]) from [<bf005648>]
(sdio_claim_host+0x40/0x48 [mmc_core])
Dec 31 17:05:44 ekadesigns user.warn kernel: [<bf005608>]
(sdio_claim_host+0x0/0x48 [mmc_core]) from [<bf03d144>]
(if_sdio_host_to_card_worker+0xb4/0x1c0 [libertas_sdio])
Dec 31 17:05:44 ekadesigns user.warn kernel: [<bf03d090>]
(if_sdio_host_to_card_worker+0x0/0x1c0 [libertas_sdio]) from
[<c004e17c>] (run_workqueue+0xb8/0x144)
Dec 31 17:05:44 ekadesigns user.warn kernel:  r6:bf03d090 r5:c3c24000
r4:c3c019e0
Dec 31 17:05:44 ekadesigns user.warn kernel: [<c004e0c4>]
(run_workqueue+0x0/0x144) from [<c004ebd0>] (worker_thread+0xa8/0xbc)
Dec 31 17:05:44 ekadesigns user.warn kernel:  r6:c004eb28 r5:c3c019e0
r4:c3c019e8
Dec 31 17:05:44 ekadesigns user.warn kernel: [<c004eb28>]
(worker_thread+0x0/0xbc) from [<c0051bc0>] (kthread+0x58/0x90)
Dec 31 17:05:44 ekadesigns user.warn kernel:  r5:c3c019e0 r4:c3c24000
Dec 31 17:05:44 ekadesigns user.warn kernel: [<c0051b68>]
(kthread+0x0/0x90) from [<c004166c>] (do_exit+0x0/0x610)
Dec 31 17:05:44 ekadesigns user.warn kernel:  r6:00000000 r5:00000000
r4:00000000
Dec 31 17:05:48 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:05:48 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas host (INT):
GET_CMD_NODE: cmd_ctrl_node is not available
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: cmdnode is NULL
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret -1
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 40, size 16, jiffies 4900
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 4900
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:49 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:05:53 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:05:53 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:05:54 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:05:54 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:05:54 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:54 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:54 ekadesigns user.info kernel: libertas: requeueing
command 1f due to timeout (#2)
Dec 31 17:05:54 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:54 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:05:58 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:05:58 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas host (INT):
GET_CMD_NODE: cmd_ctrl_node is not available
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: cmdnode is NULL
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret -1
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 40, size 16, jiffies 5900
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 5900
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:05:59 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:06:03 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:06:03 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:06:04 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:06:04 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:06:04 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:04 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:04 ekadesigns user.info kernel: libertas: requeueing
command 1f due to timeout (#3)
Dec 31 17:06:04 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:04 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:06:08 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:06:09 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas host (INT):
GET_CMD_NODE: cmd_ctrl_node is not available
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: cmdnode is NULL
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret -1
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 40, size 16, jiffies 6900
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 6900
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:09 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:06:13 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:06:13 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:06:14 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:06:14 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:06:14 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:14 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:14 ekadesigns user.info kernel: libertas: requeueing
command 1f due to timeout (#4)
Dec 31 17:06:14 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:14 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:06:18 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:06:18 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas host (INT):
GET_CMD_NODE: cmd_ctrl_node is not available
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: cmdnode is NULL
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret -1
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 40, size 16, jiffies 7900
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 7900
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:19 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:06:23 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:06:23 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:06:24 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:06:24 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:06:24 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:24 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:24 ekadesigns user.info kernel: libertas: requeueing
command 1f due to timeout (#5)
Dec 31 17:06:24 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:24 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:06:28 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:06:28 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas host (INT):
GET_CMD_NODE: cmd_ctrl_node is not available
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: cmdnode is NULL
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret -1
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 40, size 16, jiffies 8900
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 8900
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:29 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:06:33 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:06:33 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:06:34 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:06:34 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:06:34 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:34 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:34 ekadesigns user.info kernel: libertas: requeueing
command 1f due to timeout (#6)
Dec 31 17:06:34 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:34 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:06:38 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:06:38 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas host (INT):
GET_CMD_NODE: cmd_ctrl_node is not available
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: cmdnode is NULL
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret -1
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 40, size 16, jiffies 9900
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 9900
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:39 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:06:43 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:06:43 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:06:44 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:06:44 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:06:44 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:44 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:44 ekadesigns user.info kernel: libertas: requeueing
command 1f due to timeout (#7)
Dec 31 17:06:44 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:44 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:06:48 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:06:48 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas host (INT):
GET_CMD_NODE: cmd_ctrl_node is not available
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: cmdnode is NULL
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret -1
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 40, size 16, jiffies 10900
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 10900
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:49 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:06:53 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:06:53 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:06:54 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:06:54 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:06:54 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:54 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:54 ekadesigns user.info kernel: libertas: requeueing
command 1f due to timeout (#8)
Dec 31 17:06:54 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:54 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:06:58 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:06:58 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas host (INT):
GET_CMD_NODE: cmd_ctrl_node is not available
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: cmdnode is NULL
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret -1
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 40, size 16, jiffies 11900
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 11900
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:06:59 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:07:03 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:07:03 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:07:04 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:07:04 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:07:04 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:07:04 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:07:04 ekadesigns user.info kernel: libertas: requeueing
command 1f due to timeout (#9)
Dec 31 17:07:04 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:07:04 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:07:08 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:07:08 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas host (INT):
GET_CMD_NODE: cmd_ctrl_node is not available
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: cmdnode is NULL
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret -1
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 40, size 16, jiffies 12900
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 12900
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:07:09 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:07:13 ekadesigns user.debug kernel: libertas enter (INT):
command_timer_fn():971
Dec 31 17:07:13 ekadesigns user.info kernel: libertas: Command 1f timed out
Dec 31 17:07:14 ekadesigns user.debug kernel: libertas leave (INT):
command_timer_fn():985
Dec 31 17:07:14 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=2
Dec 31 17:07:14 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:07:14 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:07:14 ekadesigns user.info kernel: libertas: requeueing
command 1f due to timeout (#10)
Dec 31 17:07:14 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:07:14 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0
Dec 31 17:07:18 ekadesigns user.info kernel: NETDEV WATCHDOG: eth1:
transmit timed out
Dec 31 17:07:18 ekadesigns user.err kernel: libertas: tx watch dog timeout
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas enter (INT):
lbs_host_to_card_done():500
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas leave (INT):
lbs_host_to_card_done():511
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas enter (INT):
lbs_prepare_and_send_command():1316
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas enter (INT):
lbs_get_cmd_ctrl_node():1677
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas host (INT):
GET_CMD_NODE: cmd_ctrl_node is not available
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas leave (INT):
lbs_get_cmd_ctrl_node():1695
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas host (INT):
PREP_CMD: cmdnode is NULL
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas leave (INT):
lbs_prepare_and_send_command():1575, ret -1
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas thread:
main-thread 222 (waking up): intcounter=0 currenttxskb=00000000
dnld_sent=0
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas thread:
main-thread 333: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas thread:
main-thread 444: intcounter=0 currenttxskb=00000000 dnld_sent=0
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas enter:
lbs_execute_next_command():1747
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: OK to send command 0x001f in psstate 0
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas host:
EXEC_NEXT_CMD: sending command 0x001f
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas enter:
lbs_submit_command():1139
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas host: DNLD_CMD:
command 0x001f, seq 40, size 16, jiffies 13900
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas enter:
if_sdio_host_to_card(type 1, bytes 16):702
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas leave:
if_sdio_host_to_card():772, ret 0
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas cmd: DNLD_CMD:
sent command 0x001f, jiffies 13900
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas leave:
lbs_submit_command():1174
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas leave:
lbs_execute_next_command():1882
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas thread:
main-thread 111: intcounter=0 currenttxskb=00000000 dnld_sent=2
Dec 31 17:07:19 ekadesigns user.debug kernel: libertas thread:
main-thread sleeping... Conn=0 IntC=0 PS_mode=0 PS_State=0

Please guide me whether it is a host controller error or the marvell
firmware error or the libertas driver error ????

Regards,
Ram