[PATCH] libertas: updated readme file

[Luis Carlos Cobo Rus]

---
 drivers/net/wireless/libertas/README |   19 +++++++++++++++----
 1 files changed, 15 insertions(+), 4 deletions(-)

diff --git a/drivers/net/wireless/libertas/README
b/drivers/net/wireless/libertas/README
index c93b9b5..ba918ae 100644
--- a/drivers/net/wireless/libertas/README
+++ b/drivers/net/wireless/libertas/README
@@ -100,15 +100,19 @@ Version 5 Command:
 	iwpriv ethX beaconinterval

 BT Commands:
-	The blinding table (BT) contains a list of mac addresses that should be
-	ignored by the firmware.  It is primarily used for debugging and
-	testing networks.  It can be edited and inspected with the following
-	commands:
+	The blinding table (BT) contains a list of mac addresses that will be,
+	by default, ignored by the firmware. It is also possible to invert this
+	behavior so that we will ignore all traffic except for the portion
+	coming from mac addresess in the list. It is primarily used for
+	debugging and testing networks.  It can be edited and inspected with
+	the following commands:

 	iwpriv ethX bt_reset
 	iwpriv ethX bt_add <mac_address>
 	iwpriv ethX bt_del <mac_address>
 	iwpriv ethX bt_list <id>
+	iwpriv ethX bt_get_invert <n>
+	iwpriv ethX bt_set_invert <n>

 FWT Commands:
 	The forwarding table (FWT) is a feature used to manage mesh network
@@ -666,6 +670,9 @@ fwt_add
 				   preferred, default is 0)
 		dir		-- direction (1 for direct, 0 for reverse,
 				   default is 1)
+		rate		-- data rate used for transmission to the RA,
+				   as specified for the rateadapt command,
+				   default is 3 (11Mbps)
 		ssn		-- Source Sequence Number (time at the RA for
 				   reverse routes.  Default is 0)
 		dsn		-- Destination Sequence Number (time at the DA
@@ -728,8 +735,11 @@ fwt_list
 	where the different fields are:-
 		da		-- DA MAC address (in the form "00:11:22:33:44:55")
 		ra		-- RA MAC address (in the form "00:11:22:33:44:55")
+		valid		-- whether the route is valid (0 if not valid)
 		metric		-- route metric (cost: smaller-metric routes are preferred)
 		dir		-- direction (1 for direct, 0 for reverse)
+		rate		-- data rate used for transmission to the RA,
+				   as specified for the rateadapt command
 		ssn		-- Source Sequence Number (time at the RA for reverse routes)
 		dsn		-- Destination Sequence Number (time at the DA for direct routes)
 		hopcount	-- hop count (currently unused)
@@ -737,6 +747,7 @@ fwt_list
 		expiration	-- entry expiration (in ticks, where a tick is 1024us,
or ~ 1ms. Use 0 for an indefinite entry)
 		sleepmode	-- RA's sleep mode (currently unused)
 		snr		-- SNR in the link to RA (currently unused)
+		precursor	-- predecessor in direct routes

 fwt_list_route
 	This command is used to list a route from the FWT table. The only
-- 
1.4.3


-- 
Luis Carlos Cobo Rus       GnuPG ID: 44019B60
cozybit Inc.